Not recommended over Kynar® (and similar finishes) unless tested and approved by the buyer.Stix® must be top coated for exterior use. Not recommended for use over polyethylene or polypropylene.Not intended for immersion service or continuous water contact.Avoid rain, moisture or high humidity for the first 24 hours of curing. Do not apply in direct sunlight or on a hot surface.Apply when air, surface and product temperature are above 1.7☌ (35☏).Drywall, Plaster, Ceiling, Acoustical Tile, Wood Trim & Doors, Formica, Ceramic Tiles, Glossy Surfaces, PVC, Most Plastics, Masonry Walls, Wood, Trim, Shutters, Masonry, Stucco, Concrete, Cement Block, Galvanized Metal, Aluminum, etc. Unparalleled Adhesion to the Most Challenging Surfaces.Stix levels to a smooth surface and cleans up with soap and water. Use it on interior and exterior surfaces and topcoat with almost any type of coating including Alkyd, Acrylic Latex, Urethane, Epoxy, and Lacquer Finishes. Offers an extremely hard film when cured. Stix is also ideal for use on plaster, drywall, wood, and non-ferrous metals, where a low ambient or surface temperature would present a problem for conventional primers. We only used 12 gallons of tinted 123 the day before and this morning.Stix® Waterborne Bonding Primer is a premium quality, waterborne, acrylic urethane primer/sealer with unparalleled adhesion to the most challenging surfaces, including PVC, Vinyl, Most Plastics, Glass, Tile, Glazed Block, Glossy Paints, Pre-Coated Siding, Fiberglass, and Galvanized Metals. I’m guessing you could tint it just as much as any white base primer.
There isn’t a deep base for Stix, unlike some other primers (Fresh Start, 2-3-3), to my knowledge.
Is it possible to tint Stix primer?Ībsolutely, but your perception of how dark you are is limited. It also dries quickly, which is something I enjoy. Spray and brush applications are both simple to apply. I haven’t tried STIX on other hard surfaces, such as tile and glass, but it performs admirably on vinyl and Azek. Stix® is a low-VOC primer that leveles to a smooth surface and rinses off with soap and water. Specifications 7.00 x 7.00 x 8.00 Inches Brand Insl-x Assembled Product Dimensions (L x W x H) Is it possible to spray Stix primer? STIX paint primer is available in 1-gallon cans. Cancer and reproductive harm are at risk. On smooth surfaces, it covers approximately 400 square feet. Specifications Product Dimensions (L x W x H): 7.00 x 7.00 x 8.00 inches Waterborne formula has a low odor and low VOC content. On smooth surfaces, it covers approximately 400 square feet.Ĭancer and reproductive harm are at risk. At any time, apply a second coat or topcoat. In 30 minutes, it softens to the touch and in 1 hour, it drys to the touch.
Is Stix also a good primer? Stix is also suitable for use on plaster, drywall, wood, and other nonferrous metals where conventional primers have a low ambient or surface temperature problem. We then apply two topcoats of pigmented (tinted) catalyzed lacquer after thoroughly cleaning and abrading the doors and drawer fronts. AquaLock is very good, but you want a primer that will bond extremely well. We apply a minimum of two coats of Stix after thoroughly cleaning and abrading the doors and drawer fronts with hand sanding between each coat. Stix has a very hard finish that can be topcoated with a variety of products. Also, how many Stix primer coats should I apply? Stix®, on the other hand, can be top-coated with a high-quality latex or oil-based finish in 1 to 2 hours, depending on the overall drying conditions. Allow Stix® to cure for about 3 to 4 days after application to achieve maximum scrape-resistant resistance.
0 kommentar(er)
